Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Migrated to Confluence 4.0

...


Creates a 3D object between two 2D objects that lie on different planes. The planes do not have to be parallel.
Both profile objects must be the same type and must have the same number of vertices. For example, you can create a prism between two circles or two rectangles, but not between a circle and a rectangle. Splines and Bezier curves must have the same number of control points.
(If you want to use more than two profiles, or profiles of different type, see Profile Objects.)

...

Note: A prism is considered to be a Lofting object, and its Properties contain a Lofting Shape page. For details, see Profile Objects.

...

  1. If you want to select only simple (single-object) curves, make sure Use Compound Profile is not selected. If you want to use compound profiles, see Profile Objects.

  2. Select the two 2D objects.

    Polyline to polyline

    Spline to spline
    You do not have to select closed 2D objects. If you use open objects, a 3D surface will result.

    Anchor
    Rn3D77381
    Rn3D77381
    Anchor
    Rn3DCompoundprofilesPrismT
    Rn3DCompoundprofilesPrismT
    Anchor
    Rn3D77381T
    Rn3D77381T
    *Pri
    Anchor
    Rn3DCompoundprofilesPrism
    Rn3DCompoundprofilesPrism
    sm with Compound Profiles
    Anchor
    Rn3D77381P
    Rn3D77381P
    *
    A compound profile is an open or closed chain of connected curves or lines. You can use compound profiles when you do not want to create a polyline, or convert a chain into a polyline.
  3. Make sure Use Compound Profile is selected.

  4. Select the first compound profile, which is automatically identified as a chain. To deselect any curve in the chain, select it again (it will turn green). In this example, Profile 1 is a series of connected lines, not a polyline.

  5. When the profile is selected, click Finish Selection of Profile, or select it from the local menu.

  6. Select the second profile using the same steps.

  7. When you finish the second profile selection, the prism is created.

...

This tool is handy if you have a single profile that you want to sweep over multiple paths, or rails. In this example, there are three paths for the same profile:

Here are the results:

If you used a Compound profile for the profile, you will be able to modify the resulting 3D object by modifying the original profile object, or by moving the base point object. If you used a Compound profile for the path, you will be able to modify the resulting 3D object by modifying the original path object/s.
The sweep path does not have to be 2D. The path in this example was created using 3D Spline by Fit Points.

This is the result:

Local menu optionĀ 
Rigid Sweep: Keeps cross-sections of the solid parallel to one another along the entire path. See explanation under Profile Objects.

Compound Profiles as Paths

To use a compound profile as a path
Also see Profile Objects.

Anchor
Revolve
Revolve
Anchor
Rn3D71996
Rn3D71996
Anchor
Rn3D71996T
Rn3D71996T
R
Anchor
Xn3D98828
Xn3D98828
evolve

Anchor
Rn3D71996P
Rn3D71996P

Creates a 3D object by revolving a 2D object about a revolution axis.
By default, the profile will be revolved 360 degrees, but you can change this angle or create a spiral. See Profile Objects.

  1. If you want to select only a simple (single-object) curve, make sure Use Compound Profile is not selected. If you want to use a compound profile, see Profile Objects.

  2. If you want to select a line as the axis of revolution, make sure Select Revolve Axis is active.

  3. Select a 2D object to revolve.

  4. Select two points of a revolution axis, or, if Select Revolve Axis is active, select the axis line..

    The revolved shape is created.

...

  1. If you want to select only simple (single-object) curves, make sure Use Compound Profile is not selected. If you want to use compound profiles, see Profile Objects.

  2. Select the profiles, in the desired order. Selection order is important
  3. Select Finish from the local menu, or double-click on the last profile, to create the loft.

...