Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Reverted from v. 7

Profile objects are based on existing 2D objects. The original 2D profile remains unmodified by the 3D tool that references it.
One advantage to profile objects is that you can change them by simply editing the profile (or profiles) on which they are based. See Profile Editing.

Table of Contents

Compound Profiles

Available in TurboCAD Pro and Platinum only

A compound profile is an open or closed chain of connected curves or lines, or any set of closed curves or closed polylines. You can use compound profiles when you do not want to create a polyline, or convert a chain into a polyline. Compound profiles can be used as paths for sweeps etc., and as profiles that are swept along paths.

You can use blocks as compound profiles, however there are restrictions. You can only only use one element in a block as a path for any given operation. Also, only closed sequences of curves, lines etc. (chains) or closed objects can be used to sweep, revolve etc. All such closed objects in the block selected to sweep, revolve, etc will used in the resulting 3D object.

Prism

Image Added
Creates a 3D object between two 2D objects that lie on different planes. The planes do not have to be parallel.

Both profile objects must be the same type and must have the same number of vertices. For example, you can create a prism between two circles or two rectangles, but not between a circle and a rectangle

Splines and Bezier curves must have the same number of control points.

...

Note: A prism is considered to be a Lofting object, and its Properties contain a Lofting Shape page.

...

  1. If you want to select only simple (single-object) curves, make sure Use Compound Profile is not selected. 
    Image Added
  2. Select the two 2D objects.
    Image Added
    Polyline to polyline
    Image Added
    Spline to spline
    You do not have to select closed 2D objects. If you use open objects, a 3D surface will result.
    Image Added 
    Prism with Compound Profiles
    A compound profile is an open or closed chain of connected curves or lines. You can use compound profiles when you do not want to create a polyline, or convert a chain into a polyline.
  3. Make sure Use Compound Profile is selected.
    Image Added
  4. Select the first compound profile, which is automatically identified as a chain. To deselect any curve in the chain, select it again (it will turn green). In this example, Profile 1 is a series of connected lines, not a polyline.
    Image Added
  5. When the profile is selected, click Finish Selection of Profile, or select it from the local menu.
    Image Added
  6. Select the second profile using the same steps.
    Image Added
  7. When you finish the second profile selection, the prism is created.
    Image Added

...

Note: Compound profiles can be modified, which updates the 3D objects upon which they are based. See Profile Editing.

...

Simple Extrude

 Image Added
Creates a 3D object by extruding (sweeping) a 2D open or closed profile along a path normal to the workplane of the 2D object. If you extrude an open profile, a surface will be created.

  1. If you want to select only a simple (single-object) curve, make sure Use Compound Profile is not selected.
  2. If you want to use a compound profile, which is a series of connected lines and/or arcs, select Use Compound Profile.
    Image Added
  3. If necessary, select Finish Selection of Profile to continue.
  4. Select the 2D open or closed profile to extrude. Move the mouse to extrude the profile, or enter a value in the Height field of the Inspector Bar.
    Image Added
    If you select an open profile, the resulting 3D object will be a surface.
    Image Added
    If you select , the solid extrusion will be created on either side of the profile.
    Image Added

Extruding Multiple Profiles

You can also select multiple closed regions, or profiles, to extrude all at one time.

Make sure Use Compound Profile is selected. Select the first profile, then press Shift to select additional profiles. Each profile is extruded the same distance.
Image Added
If you select nested regions, you can create islands, and regions within islands.

Image Added

...

Note: Compound profiles can be modified, which updates the 3D objects upon which they are based. See Profile Editing.

...

Simple Extrude Shape Properties

The Properties window of an extrude object contains a Simple Extrude Shape page, in which you can set parameters defining how the object is created.
Image Added
Height: The distance of the extrusion.

Direction: Switch between one-sided and two-sided.

Solid Options: For these parameters to be accessible, the extrude must be created as a solid. Available in TurboCAD Pro and Platinum only

Draft Angle: Creates an extrusion of increasing or decreasing cross-section. Enter the angle of deviation from the extrusion path.
Image Added 
Draft Start / End Distance: If Draft Angle = 0, you can specify a draft angle by entering the offset distances.

Offset: Creates a hole in the extrusion at a distance from the outside of the extrusion equal to the Offset value.

For TC Surface Options, see TC Surface Properties.

...

Note: Text can be used as part of a compound profile while extruding.

...

Twisted Extrude

Available in TurboCAD Platinum only

Image Added
Creates a 3D object by extruding (sweeping) a 2D open or closed profile along a path normal to the workplane of the 2D object and imparting a twist. If you extrude an open profile, a surface will be created.

  1. If you want to select only a simple (single-object) curve, make sure Use Compound Profile is not selected.
  2. If you want to use a compound profile, which is a series of connected lines and/or arcs, select Use Compound Profile.
    Image Added
  3. If necessary, select Finish Selection of Profile to continue.
  4. Select the 2D open or closed profile to extrude. Move the mouse to extrude the profile, or enter a value in the Height field of the Inspector Bar.
    Image Added
    If you select an open profile, the resultant object will be a surface.
    Image Added
    If you select , the solid extrusion will be created on either side of the profile.
    Image Added

Extruding Multiple Profiles

You can also select multiple closed regions, or profiles, to extrude all at one time.

Make sure Use Compound Profile is selected. Select the first profile, then press Shift to select additional profiles. Each profile is extruded the same distance.

Image Added
If you select nested regions, you can create islands, and regions within islands.
Image Added

...

Note: Compound profiles can be modified, which updates the 3D objects upon which they are based. See Profile Editing.

...

Twisted ExtrudeShape Properties

The Properties window of an extrude object contains a Twisted Extrude Shape page, in which you can set parameters defining how the object is created.
Image Added
Height: The distance of the extrusion.

Direction: Switch between one-sided and two-sided.

For the following parameters to be accessible, the extrude must be created as a solid. Available in TurboCAD Pro and Platinum only

Draft Angle: Creates an extrusion of increasing or decreasing cross-section. Enter the angle of deviation from the extrusion path.

Image Added 
Draft Start / End Distance: If Draft Angle = 0, you can specify a draft angle by entering the offset distances.

ffset: Creates a hole in the extrusion at a distance from the outside of the extrusion equal to the Offset value.

Twist Options

Twist Angle: Specifies the total rotation of the twist.

Distance Type: Specifies where the twist will be applied to the extrusion. Normal applies the extrude between the Start and End distance. Full height applies the twist to the entire extrusion. Twist to Top applies the twist from the Start distance to the top of the extrusion.

Twist Start Distance: Where the twist starts along the extrusion.

Twist End Distance: Where the twist ends along the extrusion.

Continuity: Specifies the smoothness of the transition between the straight sections and the twisted sections. G0 is the most abrupt transition, G1 is a more moderate transition, and G2 is the smoothest transition.

For TC Surface Options, see TC Surface Properties.

Quick Pull

Available in TurboCAD Pro and Platinum only
Image Added
Pulls or pushes a 3D extension of a face by extruding 2D a closed area on the face of a 3D object. The extrusion extends along a path normal to the face of the 3D object.

The closed are must be coplanar with the Flat face of a 3D object. It may consist of:

Any closed 2D entity. E.g. a rectangl

Any area that can be hatched by picking a point (with zero gap tolerance)

Areas enclosed by crossing coplanar, linear geometry, including edges and geometry in blocks E.g. intersecting lines that create a closure

3D faces. E.g. The face of a cube

Any combination of the above. Areas created by geometry (including edges on faces) drawn coplanar to any face of a 3D solid E.g. A circle is coplanar with the face of a cube. It overlaps the edge of the cube. The edge divides the circle into two parts, one is a valid area, or intersecting lines that create a closure on the face of a 3D object, with or without defining geometry of the 3D entity.

  1. Select the 2D closed area to extrude.
    Image Added
  2. Move the mouse to extrude the face, or enter a value in the Height field of the Inspector Bar.

Image Added

 

  1. If you are specifying the height by using the mouse, click to finish the extrusion.
    Or
    If you are specifying the height by using the height field in the Inspector bar, press Enter to finish the extrusion.

Image Added

 

...

Note: If the Two Sided property is set, the solid extrusion will be created on either side of the profile.

...

Examples of areas that can be extruded:
Image Added

Quick Pull Properties

The Properties window of an Quick Pull object contains a Simple Extrude Shape page, in which you can set parameters defining how the object is created.

Height: The distance of the extrusion.

Direction: Switch between one-sided and two-sided.

Solid Options: For these parameters to be accessible, the extrusion must be created as a solid. Available in TurboCAD Pro and Platinum only.

Draft Angle: Creates an extrusion of increasing or decreasing cross-section. Enter the angle of deviation from the extrusion path.

Draft Start / End Distance: If Draft Angle = 0, you can specify a draft angle by entering the draft distances.

Offset: Creates a hole in the extrusion at a distance from the outside of the extrusion equal to the Offset value.

...

Note: The Quick Pull and the Simple Extrude tool use the same Property Value Preset. Therefore, changing the property settings in one tool will change the settings in the other.

...

Sweep

Available in TurboCAD Pro, and Platinum Only
Image Added
Creates a 3D object by driving a 2D profile along a path.

  1. Start with one or more 2D profiles. The profiles can be open or closed. Add a 2D or 3D path. Typically the path intersects the profile and is approximately perpendicular to it, but these conditions are not required.
    Image Added
  2. Activate Sweep. If the profiles consist of compound curves, make sure Use Compound Profile is active.
    Image Added
  3. Select the first 2D profile. If the profile is open, select Finish Selection of Path to end the selection. You can then select more profiles if necessary, by pressing the Shift key.
    Image Added
  4. Then select the 2D or 3D path over which you want to sweep the 2D profiles. If the sweep path consists of more than one curve, make sure Use Compound Path is active. When finished, click Finish Selection of Path.
    Image Added

As stated before, the 2D profile and the sweep path do not have to intersect. However, the results will vary depending on how far apart the profiles are.
Consider this comparison, in which the profiles on the left intersect and the profiles on the right do not.
Image Added
Here are the Sweep results: the solid on the right is swept over the offset of the sweep path, and is therefore larger.
Image Added
Local menu options

  Rigid Sweep: Use this option if you want the cross-sections of the solid to remain parallel to the original swept profile.
This solid does not use Rigid Sweep; the cross-sections of the solid are always normal to the sweep path.
Image Added
This is the same solid using Rigid Sweep; the sections are always parallel to one another, and to the original profile.

Image Added
If you view the Rigid Sweep from this angle, you can see how the sections are parallel.
Image Added
Use Edge as Path: When this option is on you can use the edge of a 3D object as a path. You cannot use this option with a compound profile. (Available in TurboCAD Platinum Only)
Image Added

Image Added
Use Loop as Path: When this option is on you can use the Loop of a 3D object as a path. A loop is all of the edges which enclose a single face of a 3D object You have to select the 3D object first, then its face. You cannot use this option with a compound profile. (Available in TurboCAD Platinum Only)
Image Added
Image Added

...

Note: If you are trying to sweep by using a block as the path, you must have the Compound Path option turned on.

...

Sweep Shape Properties

The Properties window of an sweep object contains a Sweep Shape page, in which you can set geometric parameters.
Image Added
For these parameters to be accessible, the sweep must be created as a solid. Available in TurboCAD Pro and Platinum only.
Twist Angle: The angle by which the sweep is twisted along the path.
Image Added 
Corners: Defines how the joints of multi-segmented extrusions will be formed.

Default: Sharp corners.

Image Added 
Bend: the rounding will be minimal.
Image Added
If you want a larger rounding radius, specify a Minimum Radius.
Image Added 
Crimp: Keeps internal corners sharp, performs a minimal rounding on external corners.
Image Added 
Draft Angle: Creates an extrusion of increasing or decreasing cross-section. Enter the angle of deviation from the extrusion path.
Image Added 
Draft Start / End Distance: If Draft Angle = 0, you can specify a draft angle by entering the offset distances.
Sweep does not allow you to create a TC Surface.

Rail Sweep

Available in TurboCAD Pro, Platinum and Deluxe Only
Image Added
Creates a 3D object by driving a 2D profile along a path. The profile and path do not have to touch or be in different workplanes; the profile section will be "brought" to the start of the path, made normal to the path, and swept along it.
If you are going to use Compound profiles for both the path and the profile you will need a base point. The base point specifies the point though which the profile will follow the path. To create a base point, use the Point tool and place a point at the location adjacent to the profile that you wish to be used. For example, at the end of a line, or at the center of an arc or circle.

  1. Start with one 2D profile. The profile can be open or closed. Add a 2D or 3D path. The path can lie anywhere, and in any workplane. In this example, profile and path lie in the same workplane.
    Image Added
  2. Activate Rail Sweep.
  3. If the profiles consist of compound curves, make sure Use Compound Profile is active.
    Image Added
  4. Select the first 2D profile. If the profile is open, select Finish Selection of Path to end the selection. You can then select more profiles if necessary, by pressing the Shift key.
    Image Added
  5. If you are using a Compound profile for the profile you must specify the base point to be used. at this step. Select the point you created for this purpose.
  6. Then select the sweep path. If the sweep path consists of more than one curve, make sure Use Compound Profile is active.
    Image Added
  7. The profile is brought to the path (at the base point if one is being used) and swept along it, normal to the path. The profile intersects the path at its reference point (see Components of Select Edit Mode).
    Image Added

This tool is handy if you have a single profile that you want to sweep over multiple paths, or rails. In this example, there are three paths for the same profile:
Image Added
Here are the results:
Image Added
If you used a Compound profile for the profile, you will be able to modify the resulting 3D object by modifying the original profile object, or by moving the base point object. If you used a Compound profile for the path, you will be able to modify the resulting 3D object by modifying the original path object/s.
The sweep path does not have to be 2D. The path in this example was created using 3D Spline by Fit Points.
Image Added
This is the result:
Image Added
Local menu option 

 Rigid Sweep: Keeps cross-sections of the solid parallel to one another along the entire path.

Compound Profiles as Paths

You can also use a compound profile as a path
 

Revolve

 Image Added
Creates a 3D object by revolving a 2D object about a revolution axis.
By default, the profile will be revolved 360 degrees, but you can change this angle or create a spiral.

  1. If you want to select only a simple (single-object) curve, make sure Use Compound Profile is not selected. 
    Image Added
  2. If you want to select a line as the axis of revolution, make sure Select Revolve Axis is active.
    Image Added
  3. Select a 2D object to revolve.
    Image Added
  4. Select two points of a revolution axis, or, if Select Revolve Axis is active, select the axis line..
    Image Added
    The revolved shape is created.
    Image Added

You do not have to select a closed 2D object to revolve. If you use an open object, a 3D surface will result.
Image Added 
Revolve with Compound Profiles
A compound profile is an open or closed chain of connected curves. You can use compound profiles when you do not want to create a polyline, or convert a chain into a polyline.

  1. Make sure Use Compound Profile is selected.
    Image Added
  2. Select the compound profile, which is automatically identified as a chain. To deselect any curve in the chain, select it again (it will turn green). In this example, the profile is a series of connected lines, not a polyline.
    Image Added
  3. You can select more profiles if necessary. When the profiles are selected, click Finish Selection of Profile, or select it from the local menu.
    Image Added
  4. Select two points of a revolution axis, or, if Select Revolve Axis is active, select the axis line.
    Image Added
    The revolved shape is created.
    Image Added 

    Note: Compound profiles can be modified, which updates the 3D objects upon which they are based. See Profile Editing.

Revolution Shape Properties

The Properties window of a revolve contains a Revolution Shape page, in which you can set geometric parameters.
Image Added
For the Solid parameters to be accessible, the revolve must be created as a solid. In the 3D page of the Properties window, make sure Solid is selected under Create Object As.

Spiral: The revolution will proceed outward in a spiral pattern

Taper Angle: The revolution will have a draft angle, with the section increasing or decreasing at it progresses.
The remaining parameters (Common Options) appear for both surface and solid objects

Angle of rotation: Enter a value less than 360 for a partial revolve.

Image Added 
Spiral pitch: The lateral distance between the start and end of the revolve, enabling you to create a spiral. The angle of rotation must be 360.
Image Added 
Number of coils: If Spiral pitch is nonzero, you can specify the total number of revolutions.
Image Added
Clockwise / Counterclockwise: Sets the direction of revolution. The direction depends on how the revolution axis was selected.
For TC Surface Options, see TC Surface Properties.

Lofting

Available in TurboCAD Pro and Platinum only
Image Added
Creates a 3D object by connecting 2D profiles. The profiles lie on different planes, and the planes do not have to be parallel. The profiles are connected using NURBS (Non-Uniform Rational b-Spline) calculations.
The profiles can be closed or open, but they must be consistent - all open or all closed.

  1. If you want to select only simple (single-object) curves, make sure Use Compound Profile is not selected.
    Image Added
  2. Select the profiles, in the desired order. Selection order is important
  3. Select Finish from the local menu, or double-click on the last profile, to create the loft.
    Image Added

The loft has no sharp corners at the profiles.
To create corners, you can creates two separate lofts.
Image Added
If you use open profiles, a 3D surface will result.
Image Added 
 
Lofting with Compound Profiles
A compound profile is an open or closed chain of connected curves. You can use compound profiles when you do not want to create a polyline, or convert a chain into a polyline.

  1. Make sure Use Compound Profile is selected.
    Image Added
  2. Select the compound profile, which is automatically identified as a chain. To deselect any curve in the chain, select it again (it will turn green). In this example, Profile 1 is a series of connected lines, not a polyline.
    Image Added
  3. When the profile is selected, click Finish Selection of Profile, or select it from the local menu.
  4. Select the next profiles using the same steps. If subsequent profiles are simple (not compound), you can turn off Use Compound Profile.
    Image Added
  5. When the last profile is selected, click Finish or select it from the local menu.
    Image Added 
    Note: Compound profiles can be modified, which updates the 3D objects upon which they are based. See Profile Editing.
     
  6. Lofting with Guide Lines
    You can specify guides lines when creating the loft object. In this example, the lower circle and upper square are the loft profiles. The four curves between the profiles are guide lines.
    Image Added
  7. Activate Loft, and select the loft profiles in the desired order.
    Image Added
  8. Click Select Guide Lines, or select it from the local menu.
    Image Added
  9. Select each of the guide lines.
    Image Added
  10. Click Finish or select it from the local menu. The 3D object transitions between the loft profiles, following each of the guide lines.
    Image Added
    Guide Lines
    Guide lines can be arcs, 2D or 3D Splines or lines. Beziers, and polyline cannot be used as guide lines. Guide line must touch every profile used in the loft. One end of each guide line must terminate on the first profile used in the loft The other end of that guide line must terminate on the last profile used in the loft. If guide lines do not meet these requirements they will be ignored.

Lofting Shape Properties

The Properties window of a loft contains a Lofting Shape page, in which you can minimize twist.
Image Added 
Miinimize Twist
Image Added
Effect of Minimize Twist
For TC Surface Options, see TC Surface Properties.

Branched Lofting

Available in TurboCAD Platinum only
Image Added
Creates a lofting object by defining profiles along a trunk, and profiles along two or more branches. The profiles lie on different planes, and the planes do not have to be parallel. The result is one 3D object.

  1. Select the profiles that define the trunk. The branching will start at the last profile of the trunk.
    Image Added
  2. Select Finish selection of trunk from the local menu or Inspector Bar.
  3. Select the profiles that define the first branch, starting at the profile closest to the end of the trunk.
    Image Added
  4. Select Finish selection of branch.
  5. Select profiles for additional branches the same way.
    Image Added

    Image Added
  6. When all branches are defined, select Finish. The lofting object is created.
    Image Added

Face2Face Lofting

Available in TurboCAD Pro and Platinum only

 


                              Image Added


 Creates a 3D lofting object between two faces of existing 3D objects. The result is one 3D object.

  1. Select the first face, in this example, the top of the cylinder. Selection order is important.
    Image Added
  2. Select the second face, in this case, the sloped face of the wedge.
    Image Added
  3. The result is a loft object that proceeds smoothly between the two faces. The two original objects and the new loft object are now merged into one object.
    Image Added
    The resulting object takes the properties (such as Pen) of the object where you selected the first face.

Extrude to Face

Available in TurboCAD Pro and Platinum only
Image Added
Extends a 3D object by extruding selected faces to a selected 3D object and performing a boolean.

  1. Select the face of a 3D object.
    Image Added
  2. Select the 3D object to be the target of the extrusion.
    Image Added
  3. The result is a new 3D object.
    Image Added

If the boolean option is set to Subtract, the extrusion will be subtracted from the target body, and the original 3D object from which the extrusion was made will be removed.
Image Added
You can extrude multiple faces at one time, but you can extrude to only a single 3D object.

  1. Hold down the SHIFT key to select multiple faces.
    Image Added
  2. Release the SHIFT key and select the target object.
    Image Added
  3. You will have a multiple extension.
    Image Added
    There are some limitations that must be respected to create valid results:
    Resulting extrusions must intersect the target body when extended, or the operation will be invalid.
    You cannot extrude adjacent faces.
    Adjacent faces are extended along with the extrusion face. Adjacent curved faces and adjacent slanted faces will continue their curve or slant when the selected face it extruded
    Image Added

    Image Added
    You can extend to ACIS surfaces, but only if the target body completely intersects the resulting extrusion.
    Image Added

    Image Added
    You cannot extrude a face to the same 3D object that the extrusion face belongs to.

When extruding to a ACIS surface you can remove the remnant "excess" of the target surface using the Facet Edit tool.

  1. Select the facet.
    Image Added
  2. Press the DELETE key.
    Image Added

Profile Along Path

Available in TurboCAD Pro, and Platinum Only
Image Added
Places a 2D profile along a 2D or 3D path.

  1. Select the profile you want to project, then select a point on the path where you want the projection.
    Image Added
  2. Click more points where you want profile projections.
    Image Added
    If you rotate the model, you can see the profiles in 3D.
    Image Added
  3. Select Finish from the local menu or Inspector Bar to exit the function.

Local menu options:

 Make Copy Profile: Use this profile to make multiple copies along the path. When unselected, you can Finish or select another profile.

Image Added
One Step Back: Removes profiles in the reverse order in which they were created on the path.
Image Added
Unselect Profile: Unselects the current profile, enabling you to select another one.
Image Added

...

Note: Not Currently Available in 64-bit editions

...

Graphic Along Path

Available in TurboCAD Pro, and Platinum Only
Image Added
Places a 2D profile or 3D object along a 2D or 3D path.

  1. Select the profile or object you want to project, then select a point on the path where you want the projection.
    Image Added
  2. Click more points where you want profile projections.
    Image Added
    If you rotate the model, you can see the profiles in 3D.
    Image Added
  3. Select Finish from the local menu or Inspector Bar to exit the function.

Local menu options:

Sets: Specifies a number of copies of the object that will be placed from the insertion point onward. The space between the insertions will be equal to the value in the Distance field.

Distance: Set the distance between the multiple insertions specified by the Sets field.

Delete Original: Deleted the original object.

Flip Original: Flips the inserted objects, creating a mirror of the original.

Set Graphic on Path Start Point: Sets the insertion at the start point of the path.

Set Graphic on Path End Point: Sets the insertion at the end point of the path. Sets will be ignored if this setting is on.